hp Designjet plotter and LaserJet printer parts and on site service of computers, plotters, printers and networks.

Did this site save
(or help earn) you money?
Say thanks with a
small donation.

The TWI Designjet Documents library presented here as a courtesy  of   ComputerCareOnline.com  
The owners of this website have no affiliation to Hewlett Packard nor do we claim to represent HP
in any way shape or form.   

Return to TWI Documents Library Index Page 

HP Designjet 750C Series Printers - Unusual Noise When Advancing Media

In this document:

Introductionback to table of contents

The printer is making unusual noises when media advances. The most common causes of this issue are the x-motor assembly, the cluster gear, or the overdrive clutch. Follow the steps listed in this document to accurately determine the cause of the noise and to replace the appropriate parts.

Parts required (part numbers are subject to change)back to table of contents

Part description

Models C3196A

Models C3195A

X-motor Assembly (Required)

C4705-60068

C4705-60068

Clutch/Overdrive Gear (Required)

C4705-60089

C4705-60089

Cluster Gear (Required)

C1633-40019

C1633-40019

Right Rollfeed Assembly (Required)

C4704-60199

C4704-60199

Overdrive Assembly (Required)

C4706-60121

C4705-60121

Troubleshooting stepsback to table of contents

  1. Load a sheet of media to determine if the rollfeed assembly is causing the noise.
  2. Note the location of the noise. If the noise is coming from the right side, perform troubleshooting procedures for the x-motor. If the noise is coming from the left side, perform troubleshooting procedures for the overdrive assembly, the cluster gear, and the clutch.
  3. Replace parts as needed.

Accuracy calibrationback to table of contents

  1. Place a sheet of polyester film over the top of the printer for approximately 10 minutes to stabilize the paper to environmental conditions. Use a sheet of approximately D-size (24 x 36 in/ 61 x 91 cms). Roll media may also be used. When using polyester film, load it with the matte (dull) side down.
  1. Turn the printer On.
  2. Press ENTER.
  3. Use the arrow buttons to scroll to the Utilities menu.
  4. Press ENTER.
  5. Simultaneously press ENTER and the UP Arrow buttons to access the Service Tests submenu.
  6. Remove any media that is already loaded in the printer before performing the calibration.
  7. In the Service Tests submenu, scroll to 3C Accuracy Cal, and press ENTER.
  8. "Status Calibrating" will appear during calibrating.
  9. When the calibration is finished, "Load Media for Calibration" is displayed.
  10. Load the media. If using D-size media, load the short edge as the leading edge in D-size printers and the long edge as the leading edge in E-size printers.
  11. After the media is loaded, the printer will automatically begin to plot a pattern.
  12. "Status Printing" will appear on the display while plotting.
  13. Remove the media when the printer is finished.
  14. "Create Pattern/Measure Pattern" will appear on the display.
  15. Press the DOWN arrow button to select Measure Pattern.
  16. Rotate the media so the edge with the arrows point toward the printer, and reload the media with the arrow edge print-side down.
  17. The printer will load the media, and measure the alignment marks using the line sensor on the carriage.
  18. If the calibration passes, the "Success Calibration/Press Enter" message will appear on the display.
  19. Press the PREVIOUS button back to Ready, and turn off and turn on the printer to save the calibrations.

Verifying functionalityback to table of contents

Turn the printer off, then on, and print several E or D size internal plots.

Copyright (C) Hewlett-Packard Co. 2000
This information is subject to change without notice and
is provided "as is" with no warranty.
Hewlett-Packard shall not be liable for any direct,
indirect, special, incidental or consequential damages
in connection with the use of this material.

back to table of contents

Google
 
Web computercareonline.com